Show pageOld revisionsBacklinksBack to top This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong. [[http://www.engel-und-waisen.de/index.php/Where_Do_You_Think_Peugeot_3008_Key_Fob_One_Year_From_Right_Now|Peugeot 3008 Key]] Fob Problems The mid-sized SUV from Peugeot, the 3008, has a number of positive points. It's well-designed, it drives good and has a big boot. But can it beat against strong competition in the most crowded area of the market? If your [[https://wiki.streampy.at/index.php?title=How_To_Tell_The_Good_And_Bad_About_Peugeot_207_Key_Replacement|peugeot boxer Key replacement]] keyfob doesn't work, it may have been exposed to soapy or clean tap water. You may need to take off the battery, clean it with isopropylethanol or electronic cleaner. Dead coin battery Peugeot key fobs include an insignificant coin battery that powers their remote locking as well as other functions. The battery has a limited lifespan and may wear out after years of use. Voltage testing is a straightforward method to determine if a battery is in a bad state. Multimeters are used to measure voltage between the poles that are plus and minus of the battery. This test can determine whether the battery is dead. (Image: [[https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/311159893_995841588058766_6213964028136182559_nlow.jpg|https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/311159893_995841588058766_6213964028136182559_nlow.jpg]])If you've been using your [[http://www.asystechnik.com/index.php/How_Peugeot_207_Key_Replacement_Transformed_My_Life_For_The_Better|peugeot 406 remote key programming]] 3008 for a while, and your key fobs have stopped working, there may be a problem with the receiver module. The receiver module is in charge of receiving radio frequency signals generated by the key fobs, and then sending them to the car's systems. If the receiver module is in issues, it will not be able send commands to the other modules in the car. The presence of moisture or sweat on the circuit board is another typical reason for an inoperable key fob. It can trigger short circuits, which could drain the battery and stop the feature that locks the fob's remote. If this is the case you need to bring your key fob to a technician that specializes in chip level repairs. Water damage If you dropped your key fob into the pool, tossed it into the wash or even left it in the rain for too long, water damage can be a major issue. Water is a good conductor, and can cut off circuit boards. It can also cause corrosion to the metal lines on the key fob as well as other components. A wet circuit can also cause batteries to lose their charge. If you have an extra key fob, use it to unlock or lock the [[https://m1bar.com/user/KentonMinchin/|peugeot key code]] 3008 to rule out a dead coin-cell battery as the cause of the issue. Another issue that could stop your key fob from working properly is interference signals which interfere with the signal transmitted to the receiver module. These interference signals can come from a wide range of things, including nearby radio transmitters. If you hear sloshing noises coming from your Peugeot 3008 when driving it is most likely due to a clogged condensate drain from the evaporator. You can determine this by looking for the drain holes beneath your door and blowing compressed gas into the drain holes. You can also use flexible metal wire to wiggle drain holes to remove any dirt that has collected. Air pockets can also be detected by sloshing noises. Receiver module that is defective (Image: [[https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/311170119_2306394586188303_2849487588620745484_nlow.jpg|https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/311170119_2306394586188303_2849487588620745484_nlow.jpg]])The receiver module inside the [[https://drmahtabmostofizadeh.com/question/its-time-to-expand-your-peugeot-207-key-options/|peugeot 508 key]] 3008 key fob is responsible for transmitting the remote keyless system signal from the key fob to the car's receiver. If this module is damaged, it can cause the car to not recognize the key fob. This issue can also be caused by an inactive battery or water damage. Or, interference from electronic devices operating at the same frequency. In these cases the car could display an error message saying "card not detected" on the display. There are several ways to solve this issue. You might try replacing the battery or reprogramming your key fob. You could also use a spare key in order to start the car. However, if your key fob isn't functioning after all these steps, it might have a chip defective. The best method to determine whether the key fob is equipped with a malfunctioning chip is to take it off and clean it using a paper towel and rubbing alcohol. If the chip has gone bad then you should purchase the new one. FB Series enclosures are designed for key fobs and include an optional coin battery holder for cell batteries that fits the most common types of key fob batteries. These enclosures can be customized with digital printing and CNC-machined cutouts. If your key fob has been exposed to salty or dirty tap water, your chip may be contaminated and must be cleaned. Keyless entry systems with malfunctions If you get "card not detected" This signifies that your car cannot receive an alert from your key fob. This can be caused by many factors, including the battery being weak or dead. Most often, the issue can be solved by pressing the start button using the key fob. In some cases you may need to take the keyfob to a Peugeot dealer for further repairs. Examining the battery is the first step to diagnosing the problem with a [[http://supervision.nfe.go.th/chak_rat/index.php?name=webboard&file=read&id=80761|peugeot expert key fob programming]] 3008 keyfob that doesn't lock or unlock doors. Batteries are often the root of malfunctioning key fobs. However there are other reasons that could be at play. These include worn buttons water damage, receiver module issues, and signal interference. If your Peugeot key fob has been exposed to clean tapwater, it is recommended to take the battery off. Then, dry the electronic components with paper towel. You can also try isopropyl alcohol or an appropriate cleaner for this. It is best to change the fob if it's been exposed to salt water or soapy water. If your key fob still not working, you can try to reset it by disconnecting the 12 volt battery for approximately 15 minutes. Connect the negative cable, and then the positive cable.